Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
3.1. Description of a design
3.2. Oil replacement
3.3. Replacement of laying of a cover of a head of the block of cylinders
3.4. Check and adjustment of thermal gaps in the drive of valves
3.5. Adjustment of a tension of a chain of the drive of the camshaft
3.6. Removal of an uspokoitel of a chain of the drive of the camshaft
3.7. Removal of a natyazhitel of a chain of the drive of the camshaft
3.8. Removal of the camshaft and levers of the drive of valves
3.9. Replacement of maslootrazhatelny caps of the mechanism of gas distribution
3.10. Replacement of a forward epiploon of a bent shaft
3.11. Replacement of a back epiploon of a bent shaft
3.12. Removal of a gear wheel of the drive of the oil pump
3.13. Removal of a chain and asterisks of the drive of the camshaft
3.14. Removal of the roller of the drive of auxiliary units
3.15. Replacement of laying of an inlet pipe and final collector
3.16. Removal and dismantling of a head of the block of cylinders
3.17. Removal of the sensor of pressure of oil
3.18. Removal of an oil separator of system of ventilation of a case
3.19. Removal of support of the power unit on the car with the VAZ-2106 engine
3.20. Replacement of laying of the pallet of a case
3.21. Removal of the oil pump
3.22. Dismantling of the oil pump
3.23. Dismantle of conrod and piston group on the car
3.24. Removal of the engine from the car
3.25. Dismantling and assembly of the engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 






b678569c



3-15-zamena-prokladki-vpusknojj-truby-i-vypusknogo-kollektora.html

3.15. Replacement of laying of an inlet pipe and final collector

We merge cooling liquid (see. "Replacement of cooling liquid on the car with the VAZ-2106 engine").

We remove the carburetor (see. "Removal of the carburetor").

We remove a corrugated hose from a branch pipe of a zabornik of the warmed-up air.

Having weakened a collar of fastening of a hose of the vacuum amplifier of brakes, we remove a hose from the union of an inlet pipe.

Also having weakened a fastening collar, we disconnect a hose of removal of cooling liquid from the union of an inlet pipe.

We pick up from the union of an inlet pipe the depression supply phone to the EPHH system electropneumatic valve.

Cap key "on 13" we turn off a nut of fastening of a forward eye of the engine...

. also we remove an eye.

Key "on 13" we turn off a nut of the top fastening of a zabornik of the warmed-up air...

... and nut of the lower fastening.

We remove a zabornik of the warmed-up air.

By head "on 13" with the extender it is turned off five general nuts of fastening of an inlet pipe and a final collector.

We remove an inlet pipe from hairpins of a head of the block of cylinders.

Key "on 13" we turn off two nuts of fastening of the heat-shielding screen of a starter to a final collector...

... and a key "on 10" - a bolt of fastening of the screen to an arm of the right support of the power unit.

We remove the heat-shielding screen.

We disconnect a reception pipe from a final collector (see. "Removal of a reception pipe on the car with the VAZ-2106 engine").

Key "on 13" we turn off two extreme nuts of fastening (on one from each party) a final collector.

We allocate for Passatizhami an arm of fastening of the taking-away heater radiator tube from a final collector.

We remove a final collector...

... and sealing laying of an inlet pipe and a final collector (it consists of two parts).

Before installation of a final collector and an inlet pipe we clear their privalenny planes, and also the privalenny plane of a head of the block of cylinders of a deposit and the remains of old laying. We grease new laying with a thin layer of sealant in a zone of openings under channels of the cooling system and we establish the removed details in the return sequence. We apply graphite lubricant on a carving of hairpins.


"previous page
3.14. Removal of the roller of the drive of auxiliary units
following page"
3.16. Removal and dismantling of a head of the block of cylinders