Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
3.1. Description of a design
3.2. Oil replacement
3.3. Replacement of laying of a cover of a head of the block of cylinders
3.4. Check and adjustment of thermal gaps in the drive of valves
3.5. Adjustment of a tension of a chain of the drive of the camshaft
3.6. Removal of an uspokoitel of a chain of the drive of the camshaft
3.7. Removal of a natyazhitel of a chain of the drive of the camshaft
3.8. Removal of the camshaft and levers of the drive of valves
3.9. Replacement of maslootrazhatelny caps of the mechanism of gas distribution
3.10. Replacement of a forward epiploon of a bent shaft
3.11. Replacement of a back epiploon of a bent shaft
3.12. Removal of a gear wheel of the drive of the oil pump
3.13. Removal of a chain and asterisks of the drive of the camshaft
3.14. Removal of the roller of the drive of auxiliary units
3.15. Replacement of laying of an inlet pipe and final collector
3.16. Removal and dismantling of a head of the block of cylinders
3.17. Removal of the sensor of pressure of oil
3.18. Removal of an oil separator of system of ventilation of a case
3.19. Removal of support of the power unit on the car with the VAZ-2106 engine
3.20. Replacement of laying of the pallet of a case
3.21. Removal of the oil pump
3.22. Dismantling of the oil pump
3.23. Dismantle of conrod and piston group on the car
3.24. Removal of the engine from the car
3.25. Dismantling and assembly of the engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 






b678569c



3-4-proverka-i-regulirovka-teplovykh-zazorov-v-privode-klapanov.html

3.4. Check and adjustment of thermal gaps in the drive of valves

The measurement and adjustment of gaps is carried out on the cold engine.

We uncover heads of the block of cylinders (see. "Replacement of laying of a cover of a head of the block of cylinders").

We uncover the ignition distributor (see. "Removal of a cover of the distributor of ignition").

Key "on 38" we turn a bent shaft for a nut of fastening of its pulley clockwise...

... before coincidence of a tag (drilling) on a camshaft asterisk with a ledge on the case of bearings.

At the same time the tag on a pulley of a bent shaft has to settle down opposite to a tag of VMT (long) on a camshaft drive cover. In this provision of shaft corresponding to the end of a step of compression in the fourth cylinder we check and if necessary we regulate gaps at the final valve of the fourth cylinder (the eighth cam) and the inlet valve of the third cylinder (the sixth cam).

For check of a gap we insert the wide flat probe 0,15 mm thick between the lever of the valve and a cam of the camshaft.

At a normal gap the probe has to be stretched with small effort.

For adjustment of a gap a key "on 17" we weaken an inhaling of a lock-nut of an adjusting bolt, and a key "on 13" we rotate an adjusting bolt, exposing the required gap.

We tighten a lock-nut, holding an adjusting bolt from a provorachivaniye. We check a gap and if necessary we repeat adjustment.

Consistently turning a bent shaft of the engine on 180 ° clockwise, we check and we regulate gaps of other valves in the order specified in the table:

Angle of rotation of a bent shaft, hail. No. of adjustable valves (cams)
0 8 and 6
180 4 and 7
360 1 and 3
540 5 and 2


The angle of rotation of a bent shaft can be controlled also on a distributor rotor. At turn of a bent shaft on 180 ° the rotor will turn on 90 °.

Upon termination of adjustment we establish the removed details in the return sequence.


"previous page
3.3. Replacement of laying of a cover of a head of the block of cylinders
following page"
3.5. Adjustment of a tension of a chain of the drive of the camshaft