Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
6.1. Description of a design
6.2. Adjustments of Ozone carburetors
6.3. Removal of the carburetor
6.4. Dismantling of the carburetor
6.5. Dismantling of the DAAZ-2140-1107010-70 carburetor
6.6. Dismantling of the DAAZ-2107-1107010 carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 






b678569c



6-5-razborka-karbyuratora-daaz-2140-1107010-70.html

6.5. Dismantling of the DAAZ-2140-1107010-70 carburetor

The majority of operations on dismantling of the carburetor can be executed, without removing it from the engine. The dismantling order in many cases can be any. At assembly avoid a banner of threaded connections as details of the carburetor are made of plastic alloys. It is impossible to tighten screws and nuts on the heated carburetor, it can lead to deformation of details!

Dismantling of the DAAZ-2140-1107010-70 carburetor

The crosswise screw-driver we unscrew the screw of fastening of a bracket of a pneumatic valve.

We remove a bracket...

... also we take out a pneumatic valve.

We remove a spring clamp of the valve.

We unscrew two screws got stronger a microswitch niya...

... also we remove it.

We disconnect telescopic draft of the starting arrangement from the trekhplechy lever.

By the crosswise screw-driver it is turned off five screws of a cover of the carburetor...

... also we uncover.

We disconnect telescopic draft from the lever of an axis of the air gate.

Passatizhami is taken out a float axis...

... also we remove a float.

We take a needle.

Key "on 10" we unscrew the case of the needle valve.

Under the valve case — the condensing washer.

Key "on 19" we turn off a stopper...

... also we take the filtering element.

We remove laying of a cover.

By the crosswise screw-driver it is turned off two screws of fastening of the case of the starting arrangement...

... also we remove the case assembled.

Having hooked the screw-driver, we take a rubber sealing ring.

We remove draft of the starting arrangement.

The Shlitsevy screw-driver we turn off a stopper of the case of the starting arrangement.

The Shlitsevy screw-driver with a width of edge no more than 3 mm unscrewed the adjusting screw.

By the crosswise screw-driver it is turned off three screws of a cover of the starting arrangement.

Elements of the starting arrangement.

The Shlitsevy screw-driver we unscrew the valve of the accelerating pump.

We remove a spray and the condensing rings from the valve.

By the Shlitsevy screw-driver it is turned off two air jets of the main dosing system.

Having screwed (superficially!) in an emulsion tube the self-tapping screw, we take it from a well. We arrive also with other tube.

By the Shlitsevy screw-driver it is turned off two main fuel jets.

Fuel, air jets, emulsion tubes of the main dosing system.

We remove a returnable spring.

The crosswise screw-driver we unscrew the screw of fastening three-plechego the lever.

... we remove an arm, draft, the lever and a spring.

By the crosswise screw-driver it is turned off two screws of fastening of the case of butterfly valves.

We remove the case of butterfly valves and the heat-insulating laying.

The Shlitsevy screw-driver we unscrew the case of a fuel jet of idling...

... and case of a fuel jet of transitional system.

We take out a fuel jet from the case.

By the crosswise screw-driver it is turned off four screws of a cover of the accelerating pump...

... also we remove a cover and a diaphragm.

Drift from soft metal we beat out small diffusers.

Raskontrivayem nut of an axis of a butterfly valve of the first camera.

Key "on 11" we turn off a nut.

We remove levers, washers and the plug from an axis of a butterfly valve.

Key "on 8" we turn off a nut of an axis of a butterfly valve of the second camera.

We remove the gate drive lever.

The Shlitsevy screw-driver with a width of edge no more than 4 mm we unscrew the quality screw.

We assemble the carburetor in the return sequence.


"previous page
6.4. Dismantling of the carburetor
following page"
6.6. Dismantling of the DAAZ-2107-1107010 carburetor