Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
7.1. Description of a design
7.2. Replacement of spark plugs
7.3. Removal of a cover and rotor of the distributor of ignition
7.4. Ignition distributor lubricant
7.5. Adjustment of the moment of ignition
7.6. Check and adjustment of a gap between contacts of the breaker
7.7. Removal of the distributor of ignition
7.8. Dismantling of the distributor of ignition
7.9. Removal of the condenser
7.10. Removal of the vacuum regulator of an advancing of ignition
7.11. Removal of a motionless plate of contact group of the breaker
7.12. Removal of the roller of the distributor
7.13. Removal of the coil of ignition
7.14. Councils of skilled
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 






b678569c



7-6-proverka-i-regulirovka-zazora-mezhdu-kontaktami-preryvatelya.html

7.6. Check and adjustment of a gap between contacts of the breaker

The gap between contacts of the breaker is regulated time in 15 thousand km or is more often if it is necessary (see the section "Diagnostics").

We uncover the distributor, without taking out from it high-voltage wires, and we take a cover aside.

We turn a bent shaft of the engine for a ratchet so that the plastic emphasis a rychazhka of mobile contact appeared at top of a ledge of a cam and the gap between contacts became maximum. Operations on check and adjustment of a gap between contacts of the breaker are for descriptive reasons shown on the removed distributor.

We remove a distributor rotor (see. "Removal of a cover and rotor of the distributor of ignition").

The flat probe we check a gap between contacts of the breaker. The optimum size of a gap - 0,45 mm.

In need of adjustment we weaken the screw-driver two screws of fastening of a plate of motionless contact:

one — from the vacuum regulator of an advancing of ignition...

... and the second — from contact of a wire from the ignition coil.

We insert the screw-driver into a groove of a plate of motionless contact and, shifting a plate, we try to obtain a necessary gap between contacts then we tighten screws of fastening of a plate.

Screws of fastening of a plate of motionless contact of the breaker should not be tightened too strongly not to damage the bearing of a mobile plate of the breaker.

After adjustment of a gap between contacts of the breaker it is necessary to check and if necessary to adjust an ignition advancing corner (see. "Adjustment of the moment of ignition"). For replacement of contact group we disconnect a condenser wire from a contact bolt of fastening of a tip of a wire of the distributor (see. "Dismantling of the distributor of ignition").

Key "on 7" we turn off a nut of a contact bolt...

... we take out a bolt and we remove from it a wire tip.

We unscrew two screws of fastening of a plate of motionless contact...

... also we remove contact group of the breaker.

We establish new kontakny group in the return sequence and we regulate a gap between contacts. We establish a rotor and a cover of the distributor in the return sequence.


"previous page
7.5. Adjustment of the moment of ignition
following page"
7.7. Removal of the distributor of ignition