Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
10.1. Description of a design
10.2. Adjustment of the drive of switching off of coupling
10.3. Pumping of a hydraulic actuator of coupling
10.4. Removal of the main cylinder of a hydraulic actuator of coupling
10.5. Removal of a flexible hose of a hydraulic actuator of coupling
10.6. Removal of the working cylinder of a hydraulic actuator of coupling on the car with the engine UEPA-331
10.7. Removal of the working cylinder of a hydraulic actuator of coupling on the car with the VAZ-2106 engine
10.8. Replacement of a casing and the conducted clutch plate on the car with the engine UEPA-331
10.9. Replacement of a casing and the conducted clutch plate on the car with the VAZ-2106 engine
10:10. Removal of the mechanism of the drive of switching off of coupling on the car with the engine UEPA-331
10:11. Removal of the mechanism of the drive of switching off of coupling on the car with the VAZ-2106 engine
10:12. Councils of skilled
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 






b678569c



10-9-zamena-kozhukha-i-vedomogo-diska-scepleniya-na-avtomobile.html

10.9. Replacement of a casing and the conducted clutch plate on the car with the VAZ-2106 engine

We remove the transmission (see. "Removal of the transmission").

Head "on 13" we turn off six bolts of fastening of a casing of coupling to a flywheel.

That bolts turned away easier, their heads can be tapped the hammer through a mandrel from soft metal.

We turn off bolts evenly, everyone no more than on one turn for pass not to deform a flange of a press clutch plate.

To hold a flywheel from a provorachivaniye, it is possible to screw a bolt of fastening of a case of coupling in an opening in the block of cylinders of the engine and, leaning an assembly shovel against a bolt, to insert its end between flywheel wreath teeths.

We remove a casing and the conducted clutch plate.

Establishing coupling, we focus the conducted disk the acting part of a nave towards a casing and we insert into a shlitsevy opening of a nave the aligning mandrel (for coupling of cars VAZ)...

... which has to enter an opening of the bearing located in openings of a flywheel and a flange of a bent shaft. We enshrine a coupling casing in this provision, evenly (on one turn for pass) tightening bolts the required moment (see. "Appendix") we also take out the aligning mandrel from an opening. We grease vents of a main shaft of the transmission and an external surface with the SHRUS-4 lubricant directing plugs of the bearing of switching off of coupling and we establish the removed details in the return sequence.

At removal and installation of the transmission it is impossible to opirat a main shaft on petals of a press spring of coupling - they can be damaged.

After installation of the transmission we adjust the coupling drive (see. "Adjustment of the drive of switching off of coupling").


"previous page
10.8. Replacement of a casing and the conducted clutch plate on the car with the engine UEPA-331
following page"
10:10. Removal of the mechanism of the drive of switching off of coupling on the car with the engine UEPA-331