Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
19.1. General information
19.2. Replacement of safety locks and relay
19.3. Removal of the assembly block
19.4. Zazhikaniye switch
19.5. Removal of the switch of ignition
19.6. Rechargeable battery
19.7. Cooling system fan electric motor
19.8. Generator
19.9. Starter
19.9.1. Description of a design
19.9.2. Replacement of the relay of a starter
19.9.3. Removal and dismantling of a starter 421.3708
19.9.4. Removal and dismantling of a starter 35.3708
19:10. Headlights
19:11. Understeering switch
19:12. Sound signal
19:13. Cleaner and washer of a windshield
19:14. Back door glass heating system
19:15. Control devices
19:16. Control system of the economizer of compulsory idling (ECI)
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 









b678569c


19-9-3-snyatie-i-razborka-startera-421-3708.html

19.9.3. Removal and dismantling of a starter 421.3708

We disconnect a wire of "weight" from the rechargeable battery.

We disconnect a wire of management from the traction relay.

Having shifted a rubber protective cap...

... a key "on 13" we turn off a nut of fastening of a "plus" wire (from the rechargeable battery) and we remove its tip from a hairpin of the traction relay.

Key "on 17" we turn off two nuts of fastening of a starter...

... also we remove a starter from coupling case hairpins.

Key "on 13" we turn off a nut of fastening of a power wire to the traction relay

We unscrew three screws of fastening of the traction relay.

We remove the case of the traction relay...

... also we take out a relay anchor.

We unscrew two screws of fastening of a cap.

We take off a cap and its laying.

We remove a lock washer of a shaft of an anchor.

Key "on 10" we turn off two nuts...

... also we remove a back cover.

We shift the case from hairpins.

Key "on 10" we turn off a lever axis nut, holding an axis from a provorachivaniye the screw-driver.

We take out an axis.

We take out an anchor from a forward cover and we remove the drive lever.

Operev an anchor shaft on wooden whetstone, through a key "on 14" we force down a restrictive ring.

We hook the screw-driver and we remove a lock ring.

We remove from an anchor a restrictive ring, the drive assembled and the bearing assembled.

We check serviceability of a starter similar to check of a starter 35.3708 (see. "Removal and dismantling of a starter 35.3708").

We collect and establish a starter in the return sequence. We grease screw vents of a shaft of an anchor and a nave of the coupling, a flood ring and an axis of the lever with a thin layer of Litol-24 lubricant, and bearings and necks of a shaft of an anchor — engine oil.


"previous page
19.9.2. Replacement of the relay of a starter
following page"
19.9.4. Removal and dismantling of a starter 35.3708