Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
3.1. Description of a design
3.2. Oil replacement
3.3. Replacement of laying of a cover of a head of the block of cylinders
3.4. Check and adjustment of thermal gaps in the drive of valves
3.5. Adjustment of a tension of a chain of the drive of the camshaft
3.6. Removal of an uspokoitel of a chain of the drive of the camshaft
3.7. Removal of a natyazhitel of a chain of the drive of the camshaft
3.8. Removal of the camshaft and levers of the drive of valves
3.9. Replacement of maslootrazhatelny caps of the mechanism of gas distribution
3.10. Replacement of a forward epiploon of a bent shaft
3.11. Replacement of a back epiploon of a bent shaft
3.12. Removal of a gear wheel of the drive of the oil pump
3.13. Removal of a chain and asterisks of the drive of the camshaft
3.14. Removal of the roller of the drive of auxiliary units
3.15. Replacement of laying of an inlet pipe and final collector
3.16. Removal and dismantling of a head of the block of cylinders
3.17. Removal of the sensor of pressure of oil
3.18. Removal of an oil separator of system of ventilation of a case
3.19. Removal of support of the power unit on the car with the VAZ-2106 engine
3.20. Replacement of laying of the pallet of a case
3.21. Removal of the oil pump
3.22. Dismantling of the oil pump
3.23. Dismantle of conrod and piston group on the car
3.24. Removal of the engine from the car
3.25. Dismantling and assembly of the engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 






b678569c



3-19-snyatie-opor-silovogo-agregata-na-avtomobile-s-dvigatelem-vaz-2106.html

3.19. Removal of support of the power unit on the car with the VAZ-2106 engine

We perform work on a viewing ditch or the elevator.

Cap key "on 13" we turn off nuts of two bolts of fastening of a pillow of the left forward support of the power unit to a stretcher arm, holding bolts from a provorachivaniye a cap key "on 12".

We take out bolts.

Similarly we turn off...

... also we take out two bolts of fastening of a pillow of the left forward support of the power unit to an arm of the block of cylinders of the engine.

We establish an adjustable support under the left edge of the pallet of a case and, raising the power unit a little...

... we take out a pillow of the left forward support.

In the same way we disconnect fastenings and we take out a pillow of the right forward support of the power unit. In this case we establish an adjustable emphasis under the right edge of the pallet of a case. Operations on dismantle of a pillow of a back support of the power unit are similar to operations on the car with the engine UEPA-331 and are shown in the subsection "Removal of Support of the Power Unit on the Car with the Engine UEPA-331".

For removal of a cross-piece of a back support assembled we substitute an adjustable emphasis under the lower cover of a case of the transmission.

Cap key "on 14" we turn off two bolts of fastening of a cross-piece of a back support to body arms.

Head "on 13" we turn off two nuts of hairpins of fastening of an arm of a cross-piece of a back support to a back cover of the transmission.

We remove a cross-piece assembled with a pillow and an arm.

Head "on 12" we turn off two bolts of fastening of a pillow to an arm...

... also we remove an arm.

If on pillows of support of the power unit there are cracks, gaps or peelings of rubber, replace them new and we establish in the return sequence.


"previous page
3.18. Removal of an oil separator of system of ventilation of a case
following page"
3.20. Replacement of laying of the pallet of a case