Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
3.1. Description of a design
3.2. Oil replacement
3.3. Replacement of laying of a cover of a head of the block of cylinders
3.4. Check and adjustment of thermal gaps in the drive of valves
3.5. Adjustment of a tension of a chain of the drive of the camshaft
3.6. Removal of an uspokoitel of a chain of the drive of the camshaft
3.7. Removal of a natyazhitel of a chain of the drive of the camshaft
3.8. Removal of the camshaft and levers of the drive of valves
3.9. Replacement of maslootrazhatelny caps of the mechanism of gas distribution
3.10. Replacement of a forward epiploon of a bent shaft
3.11. Replacement of a back epiploon of a bent shaft
3.12. Removal of a gear wheel of the drive of the oil pump
3.13. Removal of a chain and asterisks of the drive of the camshaft
3.14. Removal of the roller of the drive of auxiliary units
3.15. Replacement of laying of an inlet pipe and final collector
3.16. Removal and dismantling of a head of the block of cylinders
3.17. Removal of the sensor of pressure of oil
3.18. Removal of an oil separator of system of ventilation of a case
3.19. Removal of support of the power unit on the car with the VAZ-2106 engine
3.20. Replacement of laying of the pallet of a case
3.21. Removal of the oil pump
3.22. Dismantling of the oil pump
3.23. Dismantle of conrod and piston group on the car
3.24. Removal of the engine from the car
3.25. Dismantling and assembly of the engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 






b678569c



3-11-zamena-zadnego-salnika-kolenchatogo-vala.html

3.11. Replacement of a back epiploon of a bent shaft

We perform work on the elevator or a viewing ditch.

We remove a casing and the conducted clutch plate (see. "Replacement of a casing and the conducted clutch plate on the car a sdvigatel of VAZ-2106").

We roll a bolt of fastening of the transmission in a carving opening of the block of cylinders of the engine.

Holding a flywheel from a provorachivaniye the assembly shovel implanted between teeths of its wreath and leaning on the screwed bolt a head "on 17" we turn off six bolts of fastening of a flywheel to a flange of a bent shaft.

We remove a plate.

... and flywheel.

Head "on 10" we turn off two nuts of mortgage bolts of fastening of a cover of a case of coupling...

... also we uncover.

Having hooked the screw-driver...

... we take a back epiploon of a bent shaft from its cover.

We oil a working edge of a new epiploon engine...

... also we press an epiploon, using old as a mandrel.

We establish the removed details in the return sequence.


"previous page
3.10. Replacement of a forward epiploon of a bent shaft
following page"
3.12. Removal of a gear wheel of the drive of the oil pump