Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
19.1. General information
19.2. Replacement of safety locks and relay
19.3. Removal of the assembly block
19.4. Zazhikaniye switch
19.5. Removal of the switch of ignition
19.6. Rechargeable battery
19.7. Cooling system fan electric motor
19.8. Generator
19.8.1. Description of a design
19.8.2. Check of the generator
19.8.3. Removal of brush knot and regulator of tension of the generator 58.3701
19.8.4. Removal and dismantling of the generator 58.3701
19.8.5. Removal of the regulator of tension and brush knot of the generator 37.3701
19.8.6. Removal and dismantling of the generator 37.3701
19.9. Starter
19:10. Headlights
19:11. Understeering switch
19:12. Sound signal
19:13. Cleaner and washer of a windshield
19:14. Back door glass heating system
19:15. Control devices
19:16. Control system of the economizer of compulsory idling (ECI)
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 









b678569c


19-8-4-snyatie-i-razborka-generatora-58-3701.html

19.8.4. Removal and dismantling of the generator 58.3701

We disconnect a wire of "weight" from the rechargeable battery.

Cap key "on 13" we turn off a bolt of fastening of the generator to an adjusting level.

This bolt fixes at the same time and a wire of "weight" from the rechargeable battery to the engine.

We take out a bolt and we take away a wire of "weight" from the generator.

We disconnect the lower fastening of the generator and we take off a belt of its drive (see. "Adjustment of a tension and replacement of a belt of the drive of the pump of cooling liquid on the car with the engine UEPA-331").

Having turned the generator a pulley towards the engine, we disconnect a wire from conclusion "Ш" of the generator (see. "Removal of brush knot and regulator of tension of the generator 58.3701")...

... and a key "on 10" we turn off a conclusion nut "+". We remove tips of wires from a conclusion "+" the generator.

We take out the generator from a motor compartment.

We remove brush knot and the regulator of tension (see. "Removal of brush knot and regulator of tension of the generator 58.3701").

Holding a generator rotor from a provorachivaniye a hexagon "on 8", we turn off a key "on 24" a nut of fastening of a pulley.

We remove a nut, a spring washer, a pulley and a krylchatka from a generator rotor shaft.

By the Shlitsevy screw-driver it is turned off four coupling screws of covers of the generator.

Further operations on dismantling of the generator 58.3701 are almost similar to the corresponding operations on dismantling of the generator 37.3701 (see. "Removal and dismantling of the generator 37.3701"). We collect and install the generator on the car in the return sequence.


"previous page
19.8.3. Removal of brush knot and regulator of tension of the generator 58.3701
following page"
19.8.5. Removal of the regulator of tension and brush knot of the generator 37.3701